bridge

bridge — Bridging Settings

Properties

Table 51. 

Key Name Value Type Default Value Value Description
ageing-time
uint32
300
The Ethernet MAC address aging time, in seconds.
forward-delay
uint32
15
The Spanning Tree Protocol (STP) forwarding delay, in seconds.
group-address
byte array
If specified, The MAC address of the multicast group this bridge uses for STP. The address must be a link-local address in standard Ethernet MAC address format, ie an address of the form 01:80:C2:00:00:0X, with X in [0, 4..F]. If not specified the default value is 01:80:C2:00:00:00.
group-forward-mask
uint32
0
A mask of group addresses to forward. Usually, group addresses in the range from 01:80:C2:00:00:00 to 01:80:C2:00:00:0F are not forwarded according to standards. This property is a mask of 16 bits, each corresponding to a group address in that range that must be forwarded. The mask can't have bits 0, 1 or 2 set because they are used for STP, MAC pause frames and LACP.
hello-time
uint32
2
The Spanning Tree Protocol (STP) hello time, in seconds.
interface-name
string
Deprecated in favor of connection.interface-name, but can be used for backward-compatibility with older daemons, to set the bridge's interface name.
mac-address
byte array
If specified, the MAC address of bridge. When creating a new bridge, this MAC address will be set. If this field is left unspecified, the "ethernet.cloned-mac-address" is referred instead to generate the initial MAC address. Note that setting "ethernet.cloned-mac-address" anyway overwrites the MAC address of the bridge later while activating the bridge. Hence, this property is deprecated. Deprecated: 1
max-age
uint32
20
The Spanning Tree Protocol (STP) maximum message age, in seconds.
multicast-hash-max
uint32
4096
Set maximum size of multicast hash table (value must be a power of 2).
multicast-last-member-count
uint32
2
Set the number of queries the bridge will send before stopping forwarding a multicast group after a "leave" message has been received.
multicast-last-member-interval
uint64
100
Set interval (in deciseconds) between queries to find remaining members of a group, after a "leave" message is received.
multicast-membership-interval
uint64
26000
Set delay (in deciseconds) after which the bridge will leave a group, if no membership reports for this group are received.
multicast-querier
boolean
FALSE
Enable or disable sending of multicast queries by the bridge. If not specified the option is disabled.
multicast-querier-interval
uint64
25500
If no queries are seen after this delay (in deciseconds) has passed, the bridge will start to send its own queries.
multicast-query-interval
uint64
12500
Interval (in deciseconds) between queries sent by the bridge after the end of the startup phase.
multicast-query-response-interval
uint64
1000
Set the Max Response Time/Max Response Delay (in deciseconds) for IGMP/MLD queries sent by the bridge.
multicast-query-use-ifaddr
boolean
FALSE
If enabled the bridge's own IP address is used as the source address for IGMP queries otherwise the default of 0.0.0.0 is used.
multicast-router
string
Sets bridge's multicast router. Multicast-snooping must be enabled for this option to work. Supported values are: 'auto', 'disabled', 'enabled' to which kernel assigns the numbers 1, 0, and 2, respectively. If not specified the default value is 'auto' (1).
multicast-snooping
boolean
TRUE
Controls whether IGMP snooping is enabled for this bridge. Note that if snooping was automatically disabled due to hash collisions, the system may refuse to enable the feature until the collisions are resolved.
multicast-startup-query-count
uint32
2
Set the number of IGMP queries to send during startup phase.
multicast-startup-query-interval
uint64
3125
Sets the time (in deciseconds) between queries sent out at startup to determine membership information.
priority
uint32
32768
Sets the Spanning Tree Protocol (STP) priority for this bridge. Lower values are "better"; the lowest priority bridge will be elected the root bridge.
stp
boolean
TRUE
Controls whether Spanning Tree Protocol (STP) is enabled for this bridge.
vlan-default-pvid
uint32
1
The default PVID for the ports of the bridge, that is the VLAN id assigned to incoming untagged frames.
vlan-filtering
boolean
FALSE
Control whether VLAN filtering is enabled on the bridge.
vlan-protocol
string
If specified, the protocol used for VLAN filtering. Supported values are: '802.1Q', '802.1ad'. If not specified the default value is '802.1Q'.
vlan-stats-enabled
boolean
FALSE
Controls whether per-VLAN stats accounting is enabled.
vlans
array of vardict
Array of bridge VLAN objects. In addition to the VLANs specified here, the bridge will also have the default-pvid VLAN configured by the bridge.vlan-default-pvid property. In nmcli the VLAN list can be specified with the following syntax: $vid [pvid] [untagged] [, $vid [pvid] [untagged]]... where $vid is either a single id between 1 and 4094 or a range, represented as a couple of ids separated by a dash.